Hierarchically Structured Porous Piezoelectric Polymer Nanofibers for Energy Harvesting.

Hierarchically porous piezoelectric polymer nanofibers are prepared through precise control over the thermodynamics and kinetics of liquid-liquid phase separation of nonsolvent (water) in poly(vinylidene fluoride-trifluoroethylene) (P(VDF-TrFE)) solution. Hierarchy is achieved by fabricating fibers with pores only on the surface of the fiber, or pores only inside the fiber with a closed surface, or pores that are homogeneously distributed in both the volume and surface of the nanofiber. For the fabrication of hierarchically porous nanofibers, guidelines are formulated. A detailed experimental and simulation study of the influence of different porosities on the electrical output of piezoelectric nanogenerators is presented. It is shown that bulk porosity significantly increases the power output of the comprising nanogenerator, whereas surface porosity deteriorates electrical performance. Finite element method simulations attribute the better performance to increased volumetric strain in bulk porous nanofibers.

Does dynamic vulcanization induce phase separation?

Immiscible and miscible blends of poly(vinylidene fluoride) (PVDF) and acrylic rubber (ACM) were subjected to dynamic vulcanization to investigate the effect of crosslinking on phase separation. As a result of different processability, mixing torque behavior of miscible and immiscible blends was significantly different from one another. Scanning electron microscopy (SEM) was used to investigate the morphology of the system. After dynamic vulcanization, submicron ACM droplets were observed in the samples near the binodal curve of the system under mixing conditions. Small angle X-ray scattering (SAXS) and differential scanning calorimetry (DSC) analysis were used to investigate the effect of dynamic vulcanization on the lamellar structure of the system. It was shown that for samples near the boundary of phase separation, increasing the crosslink density led to a decrease in the lamellar long period (L) as a sign of increment of crosslink density induced phase decomposition. Effects of shear rate on the final morphology of the system were investigated by changing the mixing temperature and by comparing the results of dynamic vulcanization at one phase and two phase regions.

A new approach for mechanisms of ferroelectric crystalline phase formation in PVDF nanocomposites.

This paper proposes a new mechanism for ferroelectric polymorph formation of poly(vinylidene fluoride) (PVDF) nanocomposites. Utilizing time-resolved Fourier transform infrared spectroscopy (FTIR), the real-time investigation of the conformational changes of the PVDF chain segment during crystallization of neat PVDF and the corresponding nanocomposite was performed. Whilst PVDF-clay nanocomposites exhibited mainly the ß crystal phase coexisting with the γ phase at low Tc (Tc < 155 °C), the coexistence of γ and ß crystalline phases was found at a high Tc temperature range (Tc > 155 °C). Experimental results were compared with predictions of the Lauritzen and Hoffman (LH) model and discrepancies were observed between model predictions and experiments. We then recalled the Brochard-de Gennes (BD) model and proposed that different crystalline polymorph formation should be inferred as a transition in the reeling-in rate dependence of the friction coefficient on nanocomposites rather than as a change in the relative rates of secondary nucleation and substrate completion. Combining LH and BD models we proposed a new mechanism to answer the contradictory questions associated with nanocomposite polymorphism. The coexistence of different polymorphs in nanocomposites was proposed to be associated with the coexistence of fast and slow moving chains, which were recognized as the free and adsorbed chains by nanofillers.

Influence of miscibility phenomenon on crystalline polymorph transition in poly(vinylidene fluoride)/acrylic rubber/clay nanocomposite hybrid.

In this paper, intercalation of nanoclay in the miscible polymer blend of poly(vinylidene fluoride) (PVDF) and acrylic rubber(ACM) was studied. X-ray diffraction was used to investigate the formation of nanoscale polymer blend/clay hybrid. Infrared spectroscopy and X-ray analysis revealed the coexistence of ß and γ crystalline forms in PVDF/Clay nanocomposite while α crystalline form was found to be dominant in PVDF/ACM/Clay miscible hybrids. Flory-Huggins interaction parameter (B) was used to further explain the miscibility phenomenon observed. The B parameter was determined by combining the melting point depression and the binary interaction model. The estimated B values for the ternary PVDF/ACM/Clay and PVDF/ACM pairs were all negative, showing both proper intercalation of the polymer melt into the nanoclay galleries and the good miscibility of PVDF and ACM blend. The B value for the PVDF/ACM blend was almost the same as that measured for the PVDF/ACM/Clay hybrid, suggesting that PVDF chains in nanocomposite hybrids interact with ACM chains and that nanoclay in hybrid systems is wrapped by ACM molecules.